ACDP로 칩을 제거하거나, 용접, 와이어 커팅할 필요없이 작업을 진행합니다.
사용 방법: PC에서 조작하기에 휴대폰으로 작업을 진행하기가 됩니다.
테스트 연결 방식의 변경: 납땜 인두로 용접 작업으로 용접 필요 없는 전용 커넥터로 연결하기로 변경되었습니다.
수동 확인부터 스마트형 모니터링으로 전환: 눈으로 관찰하면서 시도하는 작업을 진행하는 과거이며, 지금은 완전 자동으로 측정 산법을 취합니다. 이미지로 연결할 때의 안전성을 확보하고, 데이터가 손상되거나 잃어버리지 않도록 합니다.
서비스 변화: 오프라인에서 온라인로 바꿔, 동기식 서비스로 전환합니다.
주의: 본 제품은 기본 버전입니다.
특정 차종(BMW등) 에 관한 유료 가능 모듈이 원본 가격에 포함되지 않습니다.
각 모듈에 따라 따로 비용이 있습니다.
정확한 비용 정보를 원하시면 한국 시장 업무 담당 토마토에게 문의하십시오.
메일 주소: tomato@lockpick.cn
Dismantle free, bonding wire free;
Operation mode: PC side transform into phone side;
Attended mode: solder with the soldering bit transform into special connector;
Human visual transform into intelligent monitoring: Automatic detection algorithm will ensure the reliability of indication and protect data;
Service mode: Offline transform into online, synchronization service;
EEPROM Programming(included):
Support 93/24/25/35/95 Series EEPROM in circuit programming (ICP) and on adapter board programming(OBP).
If you need to use the function below, please consult your Miss fruits.
BMW module Programming：
①：Support CAS1-CAS3+ IMMO key programming and mileage reset through
OBD mode.
②：Support CAS4/CAS4+ IMMO key programming and mileage reset through
OBD mode.Support 9S12DXP512/9S12XEP100.No need to downgrade
CAS version. Much safer and More efficient! Operation Time reduced from
dozens of minutes to few minutes.
③：Support CAS3+/3++,CAS4/4+key programming and mileage reset by
ICP.Data reading and writing without lifting the pin. No removing any
components. Intelligent detection.
④：Support FEM/BDC IMMO key programming and mileage reset.Fully
automatic mode matching.Safe,reliable and fast!Support FEM/BDC module
restore,FEM/BDC backup and write anti-theft data at the same time.
⑤：Support key unlocking, key refresh function.
⑥：Repair (FRM) Footwell module data without coding.
⑦：Support BMW 8HP (F/G chassis) gearbox refresh. 6HP (F chassis)
gearbox refresh and cloning.
⑧：Support CAS1-CAS4 data restore. It can modify vehicle frequency, VIN,
ISN code, or replace CAS module by modifying EE data.
⑨：Support OBD restore CAS3/CAS3+/CAS3+ problem caused by downgrade.
⑩：Read ISN codes of N20/N55/N13 by OBD or without openning the DME
shell. Read ISN code of MSV70/MSV80/MSD80 without opening the DME
shell. Read ISN code of other models (B38, etc.) by opening the shell.
⑪：Read ISN code of MSV90/B48 by OBD.
⑫：Read & Write ISN code on Bench.Support full versions of
N13/N20/N63/S63/N55/B38 etc.
⑬：Ecu Clone. Support BMW N13, N20, N63,S63,N55 and B38 Dflash and
Pflash reading/writing.
⑭：Support instrument calibration of BMW full range.
Jaguar/Land Rover KVM module Programming：
Support Adding key and all-key-lost for new Jaguar and land rover with KVM module after year 2015.
Porsche BCM module Programming：
Support Adding key and all-key-lost for new Porsche after year 2010
Volkswagen MQB module Programming：
Support parts of VDO key programming/mileage adjustment of VW MQB platform via OBD, and Passat MMC(NEC D70F3525+95320)instrument adjustment after years 2015 by ICP mode.
Fujitsu CPU module Programming：
Support Fujitsu CPU MB91F(Honda Fit,KIA K3/K5,Sonata 9,etc.)Mileage adjustment.
Function of Airbag ECU reset/maintenance reset is under development...
Mercedes-Benz,Audi and various models is under development...
    
|
